manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 130

504PRO_604PRO_o-m2_00

-

11-14 Maintenance/Setting

504/604 PRO Baler

•

Lubricate the knife lever only on balers with cutting device XtraCut 17(see page 11-14).

Maintenance after Every 500 Bales or more often, in sandy conditions twice per day

•

Sharpen or replace the knives

•

Lubricate several parts of the baler (see page 11-14)

Maintenance after 3000 bales and before/after the baler is not used for more than 6 weeks

•

Lubricate several parts of the baler (see lubrication chart (see page 11-14)

Maintenance at the End of the Season

•

Tighten the Chains of the Pick-up, Bale Chamber and Feed Rotor

•

Lubricate several parts of the baler (see page 11-14))

Maintenance at the Start of the Season

•

Adjust the Disc Brake of the Net Tying Unit (see page 11-5).

•

Adjust the Shock Absorbers of the net tying system (see page 11-6).

After 6 years

•

Replace the hydraulic hoses, ask your certified technician to replace the hoses

11.8.2

Lubrication Chart

1. Make sure the PTO shaft is switched off, tractor engine is stopped and the key is removed.

2. Lubricate the parts with the referred lubricant and according to the interval in the tables in this paragraph.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands