manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 94

504PRO_604PRO_o-m2_00

-

504/604 PRO Baler

Preparing the Equipment Baler 7-31

Figure 51. Cutting knive

7.8.5

Assembly and Disassembly of the Cutting Device Knives

NOTICE

By removing individual knives the cut length of the baling material can be changed. If no cutting function is desired for a
longer period of time, all knives can be removed and replaced by blank knives.

WARNING:

Injury may occur. Wear protective gloves and use a suitable tool while working with the knives. If any

maintenance or assembly work is carried out with the tailgate open, the tailgate must be hydraulically secured against
lowering for safety reasons

For the following working steps: refer to chapter

Moving in and out the cutting device

•

Move cutting device to cutting position.

•

Lower Hydroflexcontrol-bottom door half way.

•

Open and secure tailgate (see page 2-15)

•

Rotate knife axle lever down and forward 90 degrees until it contacts lower stop (see Figure 52 on page 7-32).

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands