manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 20

504PRO_604PRO_o-m2_00

-

504/604 PRO Baler

Safety Messages 2-7

Locking of the belt tightener for maintenance purposes

2.3.2

Safety Signs

Hazards that can not be secured by construction are labelled with safety signs. Signs which are described in the following.

located on your machine contain important and useful information that will help you operate your equipment safely. Refer to the Parts Manual for
safety sign location. To assure that all signs remain in place and recognizable, follow instructions given below.

•

Keep signs clean. Use soap and water

–

not mineral spirits, abrasive cleaners, or other similar cleaners that will damage the safety sign.

•

Replace any damaged or missing signs. When attaching signs, the temperature of the mounting surface must be at least 40°F (5°C). The
mounting surface must also be clean and dry.

•

When replacing a machine component with a sign attached, replace sign also.

•

Replacement signs can be purchased from your Vermeer equipment dealer.

Decal

Explanation

DANGER:

Baler intake can pull you in, resulting in

death or serious injury. Stay clear of pick-up reel and
feed intake area. Baler may take in crop or twine faster
than you can let go.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands