manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 115

504PRO_604PRO_o-m2_00

-

504/604 PRO Baler

Operation Instructions 10-3

2. Use the single acting valve in the tractor to open the tailgate.

The bale leaves the chamber and an arrow appears in the display.

3. Move the single acting valve in the tractor to

‘

float' to lower the tailgate completely. This ensures that

•

The tailgate closes with minimal wear on the hydraulic pump of the tractor.

•

Gives sufficient time for the locking hook and bolt to engage.

•

Allows the net knife reset cylinder to fully retract in preparation for the next wrapping cycle.

Keep the single acting valve in 'float' during baling.

4. Wait for a short signal tone, this indicates that the tailgate is closed completely and locked.

On the display a closed tailgate is shown.

5. Start driving and pick up material for the next bale.

10.3

Disconnect the Baler from the Tractor

Park the baler

1. Make sure the ground under the baler wheels and tongue jack is firm and level.

2. Make sure the baling chamber is empty and the tailgate is closed.

3. Depressurize the hydraulic system, see the procedure below.

Depressurize the hydraulic system

1. Start the tractor engine.

2. Lower the pick-up completely with the double acting valve in

‘

float

’

.

3. On the control box push the button

to select the knives.

4. Use the double acting valve in the tractor to retract the knives.

5. Wait to release the valve lever after the knives are retracted for another 5 seconds.

This ensures that the hydraulic accumulators are emptied.

6. While the tractor engine still runs, set the double acting valve in the tractor to

‘

float' to depressurize all circuits.

7. Push the button

to select and depressurize the cutting device.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands