manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 4

504PRO_604PRO_o-m2_00

-

504/604 PRO Baler

Introduction

accessories installed on Agricultural Equipment which were not manufactured or installed by Vermeer authorized dealers; (xi) the elements; (xii)
collision or other accident.

•

Any Agricultural Equipment whose identification numbers or marks have been altered or removed.

•

Any Agricultural Equipment which any of the required or recommended periodic inspection or services have been performed using parts not
manufactured or supplied by Vermeer or meeting Vermeer Specifications including, but without limitation, lubricants (oil, grease), belt lacings,
and hydraulic fluids.

•

New Agricultural Equipment delivered to the retail purchaser in which the equipment /warranty registration has not been completed and
returned to Vermeer within ten (10) days from the date of purchase.

•

Any defect that was caused (in Vermeer's sole judgment) by operation of the Agricultural Equipment not abiding by standardoperating
procedures outlined in the Operator's Manual.

•

Tire Limited Warranties and support are the responsibility of the respective product's manufacturer.

•

Transportation costs, if any, of transporting to the Vermeer dealer.

•

The travel time and expenses of the Vermeer dealer's service personnel to make a repair on the retail purchaser's site or other location.

•

In no event shall Vermeer's liability exceed the purchase price of the product.

•

Vermeer shall not be liable to any person under any circumstances for any incidental or consequential damages (including but not limited to,
loss of profits, out of service time) occurring for any reason at any time.

•

Diagnostic and overtime labor premiums are not covered under this Limited Warranty Policy.

•

Depreciation damage caused by normal wear, lack of reasonable and proper maintenance, failure to follow operating instructions, misuse, and/
or lack of proper protection during storage.

•

Accessory systems and electronics not of Vermeer's manufacture are warranted only to the extent of such manufacturer's respective Limited
Warranty, if any.

•

Wear items which are listed by product group below:

COMMON WEAR ITEMS

: roller chain, sprockets, clutches, clutch components, knives, bolts/torqued parts, hoses (unlessotherwise specified

under extended warranty).

BALE MOVERS:

chains, motor sprocket, rear sprocket.

BALE PROCESSORS:

coupler chain, DRV couplers, feed roller belting, flails.

BALE WRAPPERS:

extension chain, film dispenser gear set, gearbox housing, knife assembly, plastic sprocket, shear bolts.

BALERS

: belt lacings/cables, pickup teeth, scraper knives, service items, twine knives.

RAKES/TEDDERS:

teeth, tines.

MOWERS

: blades, caps, discs, shoes.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands