manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 105

504PRO_604PRO_o-m2_00

-

9-2 Operating the Machine Baler

504/604 PRO Baler

WARNING:

Injury may occur. Never leave tractor controls unattended while the implement is operating. When carrying

out work on the opened tailgate: Follow Shutdown Procedure (see page 6-1), and use appropriate safeguards when
working on or around machine.

WARNING:

Injury may occur. Contact with baler or bales can result in death or serious injury. Keep all spectators and

other workers away from baler and work area while in operation. Survey area around baler for persons or obstacles
before moving the machine and at all times while working with it.

Figure 60. Keep spectators away

9.2

Laying Swaths (windrows)

The full performance of the machine and good bale formation can only be achieved when the swaths are prepared carefully. Lay swath evenly.

The width of the swath should be:

Pick-up width

7.4 ft (2.25 m)

optimum width of the swath (approx.)

4 ft (1.22 m)

9.3

Pick-up Baler

Several hydraulic functions can be operated with only one tractor's hydraulic control by means of a electro-hydraulic manifold block (hydraulic
switch).

Move cutting device into cutting position

•

[10] Open shutoff valve(see Figure 61 on page 9-3) at the hydraulic quick coupler with red marking.

•

[1] Press key or screen softkey (see Figure 62 on page 9-3)to activate the pick-up.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands