Vermeer 504 PRO Operator And Maintenance Manual Download Page 71

Page: 71 / 153

504PRO_604PRO_o-m2_00

7-8 Preparing the Equipment Baler

504/604 PRO Baler

Keep driveline shields in place at all times. Ensure shields turn and
telescope freely.

Wear close-fitting clothing and confine long hair.

Figure 29. Rotating driveline

WARNING:

During operation there is potential of the driveline slipping off the tractor power take-off and causing

injuries and/or damages. Ensure that the driveline is properly connected to the tractor.

NOTICE

Ensure angle of driveline constant velocity joint never exceeds 80° (see page 7-9). Damage to driveline and/or tractor may
result.

•

Follow the operating instructions of the driveline manufacturer as well as national relevant signs with type approval for driveline protection.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Search results

Summary of Contents for 504 PRO

Reviews:

Brands by name

Popular brands

Vermeer 504 PRO, Operator And Maintenance Manual

Search results

Summary of Contents for 504 PRO

Reviews:

Brands by name

Popular brands