manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 72

504PRO_604PRO_o-m2_00

-

504/604 PRO Baler

Preparing the Equipment Baler 7-9

Figure 30. Angle of driveline

Only the driveline prescribed by the manufacturer may be used! A key-type overrunning clutch as integrated part of the driveline protects the
machine drive.

Figure 31. Driveline

WARNING:

Injury may occur. (see page 7-9) Protective tube and guard cone of the driveline and power take-off

protection must be fitted and be in proper condition. Ensure before switching on the driveline that the selected speed of
the tractor is in conformity with the permissible speed and direction of rotation of the machine (540 rpm).

Reduce engine speed to idle before switching off power take-off.

7.4.1

Driveline

–

couple to tractor

NOTICE

Do not attach a baler equipped for 540 rpm PTO to a 1000 rpm PTO; damage to baler may result.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands