Vermeer 504 PRO Operator And Maintenance Manual Download Page 101

Page: 101 / 153

504PRO_604PRO_o-m2_00

504/604 PRO Baler

Transporting the Machine 8-3

Figure 56. Tractor wheels

8.2

Minimum weight/transport speed (per ASABE standard,

“

Safety for Agricultural

Equipment

”

)

WARNING:

Maximum towing speed: 20 mph (32 km/h). Loss of steering or braking control can result in death or serious

injury. Use a tractor that is large enough for sufficient steering and braking control. Do not tow equipment that does not
have brakes at speeds over 20 mph (32 km/h). Do not tow with an underweight tractor.

Max. baler weight (empty bale chamber): 8400 lb (3810 kg) Min. tractor weight (road transport): 7200 lb (3266 kg)(see page 8-1)

8.3

Preparing for Transport

•

The bale chamber must be completely emptied (acc. to road traffic regulations).

•

Lift pick-up to highest position and secure pick-up with both chains (left and right side of the pick-up)(see Figure 57 on page 8-4)

•

Close shut off valve [11] (see Figure 58 on page 8-4) at the hydraulic tube of the pick-up. By this the pick-up is secured into the highest position.

•

Remove any crop material hanging loosely from the baler.

•

Connect driveline to tractor power take-off (see page 7-7)

“

Driveline".

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Search results

Summary of Contents for 504 PRO

Reviews:

Brands by name

Popular brands

Vermeer 504 PRO, Operator And Maintenance Manual

Search results

Summary of Contents for 504 PRO

Reviews:

Brands by name

Popular brands