manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 116

504PRO_604PRO_o-m2_00

-

10-4 Operation Instructions

504/604 PRO Baler

8. Switch off the tractor engine and remove the key.

Disconnect the Baler

1. Install the tongue jack(see page 7-1).

2. Disconnect the cables of electrical power supply, lighting and control panel and store in storage slots.

3. Disconnect the hydraulic hoses and connect them to the dummies and store in storage slots.

4. Disconnect the PTO shaft and Place the drive shaft on a drive shaft support.

5. Disconnect the baler.

10.4

Stopping the Machine in the Field

To work safely it is important to follow the Shutdown procedure (see page 6-1) before doing maintenance, troubleshooting, or making
adjustments.

1. Park the tractor with the baler at a safe location on a solid level ground.

2. Release the pressure of the hydraulic system (see page 10-3)

Follow the Shutdown Procedure (see page 6-1)

3. Make sure the PTO shaft is switched off, stop the tractor engine and remove the key.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands