Utax P-4531DN Operation Manual Download

Page: 148 / 352

Operation Panel

4-70

Restart Network (Restarting the optional Network Interface Kit)

After all network related settings have been done, restart the network card of the device. This is mandatory to make the
settings effective.

In the

Wi-Fi Settings

menu, press





to select

Restart

Network

Press

[OK]

. A confirmation screen appears.

Press

[Yes]

(

[Left Select]

). The message

Restarting...

Please wait.

appears and the network is restarted.

Pressing

[No]

(

[Right Select]

) returns to the

Basic

menu without

restarting the network.

Wired Netwk. Set (Wired Network Settings)

Configure wired network settings.

The options available in the Wired Network are as follows:

• TCP/IP Settings (TCP/IP Settings)...4-70
• LAN Interface (LAN Interface setting)...4-77

In the

Network

menu, press





to select

Wired Netwk. Set

Press

[OK]

. The

Wired Netwk. Set

menu screen appears.

TCP/IP Settings (TCP/IP Settings)

This selects the TCP/IP settings.

The options available in the TCP/IP Settings are as follows:

• TCP/IP (Enable/Disable TCP/IP)...4-71
• IPv4 Setting (TCP/IP IPv4 settings)...4-71
• IPv6 Setting (TCP/IP IPv6 settings)...4-74

In the

Wired Netwk. Set

menu, press





to select

TCP/IP

Settings

Press

[OK]

. The

TCP/IP Settings

menu screen appears.

Wi-Fi Settings:

Restart Network

Exit

Setup

TCP/IP Settings

Restart.

Are you sure?

Yes

Wired Netwk. Set:

TCP/IP Settings

Exit

LAN Interface

TCP/IP Settings:

IPv6 Setting

Exit

IPv4 Setting

TCP/IP

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands