Utax P-4531DN Operation Manual Download | Manualshive

Page: 152 / 352

background image

Operation Panel

4-74

3

Use the numeric keys or press



or



to set the default gateway.

You can set any value between 000 and 255.
Increase or reduce the figures by pressing



or



.

Use



and



to move the position being entered, which is shown

highlighted.

4

Press

[OK]

. The default gateway is stored and the

IPv4 Setting

menu reappears.

IPv6 Setting (TCP/IP IPv6 settings)

This selects the settings for TCP/IP (IPv6).

TCP/IP (IPv6) is based on the current Internet protocol, TCP/IP (IPv4). IPv6 is the next-generation Internet protocol and
expands the available address space, which resolves the problem of the lack of addresses under IPv4, while also
introducing other improvements such as additional security functionality and the capacity to prioritize data transmission.

1

In the

TCP/IP Settings

menu, press



or



to select

IPv6

Setting

.

2

Press

[OK]

. The

IPv6 Setting

menu screen appears.

The options available in the TCP/IP (IPv6) settings are as follows:
• TCP/IP (IPv6) (Enable/disable TCP/IP (IPv6))...4-74
• Link Local (Check the IP Address of the machine.)...4-75
• Manual Settings (Manual Settings of TCP / IP (IPv6))...4-75
• RA (Stateless) (RA (Stateless) setting)...4-76
• DHCPv6 (DHCPv6 setting)...4-77

IMPORTANT

The Link Local, Manual Settings, RA (Stateless) and

DHCPv6 menu options for TCP/IP (IPv6) are displayed when TCP/IP
(IPv6) is enabled.

TCP/IP (IPv6) (Enable/disable TCP/IP (IPv6))

This specified whether TCP/IP (IPv6) is used.

1

In the

IPv6 Setting

menu, press



or



to select

TCP/

IP(IPv6)

.

2

Press

[OK]

. The

TCP/IP(IPv6)

screen appears.

3

Press



or



to select whether TCP/IP (IPv6) is enabled.

4

Press

[OK]

. The TCP/IP (IPv6) setting is set and the

IPv6 Setting

menu reappears.

IPv6 Setting:

Exit

01

IPv6 Setting

IPv6 Setting:

Off

01

On

02

*

«
...
150
151
152
153
154
...
»

Summary of Contents for P-4531DN

































































































































































































































































































































































Reviews:

No comments

Related manuals for P-4531DN

Brand: Oki Pages: 33

Brand: Oki Pages: 52

Brand: Oki Pages: 11

Brand: OKIDATA Pages: 58

Brand: Octave Pages: 2

Brand: IBM Pages: 334

Brand: IBM Pages: 428

Brand: IBM Pages: 316

Brand: IBM Pages: 210

Brand: MakerBot Pages: 48

Brand: Ricoh Pages: 268

Brand: Tally Pages: 28

Brand: Sagem Pages: 126

Brand: Creality 3D Pages: 65

Brand: Xprinter Pages: 40

WorkCentre 5845

Brand: Xerox Pages: 14

Brand: Epson Pages: 61

Brand: Epson Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands