Utax P-4531DN Operation Manual Download | Manualshive

Page: 154 / 352

background image

Operation Panel

4-76

Default Gateway (Gateway setting)

Specify the default gateway of TCP/IP (IPv6).

1

In the

Manual Settings

menu, press



or



to select

Default

Gateway

.

2

Press

[OK]

. The

Default Gateway

screen appears.

3

Use the numeric keys to set the default gateway.

You can set any value between 0000 and FFFF.
Use



and



to move the position being entered, which is shown

highlighted.

4

Press

[OK]

. The default gateway is stored and the

Manual

Settings

menu reappears.

RA (Stateless) (RA (Stateless) setting)

The IPv6 router communicates (transmits) information such as the global address prefix using ICMPv6. This information is
the Router Advertisement (RA).

ICMPv6 stands for Internet Control Message Protocol, and is an IPv6 standard defined in the RFC 2463 "Internet Control
Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification".

1

In the

IPv6 Setting

menu, press



or



to select

RA(Stateless)

.

2

Press

[OK]

. The

RA(Stateless)

menu screen appears.

3

Press



or



to select

RA(Stateless)

.

4

Press

[OK]

. The

RA(Stateless)

screen appears.

5

Press



or



to select whether RA (Stateless) is enabled.

6

Press

[OK]

. The RA (Stateless) setting is set and the

IPv6 Setting

menu reappears.

Note

Before you enter the gateway, be sure to set the

RA(Stateless)

setting to

Off

.

Default Gateway

1123 : 1451 : 1167 :

1189

:1123 : 1451 :1167 : 1189

RA(Stateless):

RA(Stateless)

01

RA(Stateless):

Off

01

On

02

*

Note

When

On

is set, IP addresses are shown in "IP

Address 1 (to 5)" after network restart.

«
...
152
153
154
155
156
...
»

Summary of Contents for P-4531DN

































































































































































































































































































































































Reviews:

No comments

Related manuals for P-4531DN

Brand: EasyThreed Pages: 4

Brand: EASYPRINT Pages: 37

Brand: Oki Pages: 32

Brand: Oki Pages: 2

Brand: Oki Pages: 96

Brand: Oki Pages: 2

Brand: Oki Pages: 78

Brand: Oki Pages: 2

Brand: Oki Pages: 2

Brand: Oki Pages: 32

Brand: Oki Pages: 52

Brand: Oki Pages: 49

Brand: Oki Pages: 48

Brand: Oki Pages: 161

Brand: Oki Pages: 6

Brand: Oki Pages: 84

Brand: Oki Pages: 51

Brand: Oki Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands