Utax P-4531DN Operation Manual Download

Page: 180 / 352

Operation Panel

4-102

Format SD Card (Formatting the SD card)

The printer is equipped with a slot for an SD card.

A SD card must be formatted before it can be used in the printer. Formatting allows data to be written to the SD card.

When a new SD card is inserted in the printer's slot,

Format SD Card

will appear on the message display.

In the

Device Common

menu, press





to select

Format SD

Card

Press

[OK]

. A confirmation screen appears.

Press

[Yes]

(

[Left Select]

). The

Formatting SD card...

screen appears and SD card formatting begins. Once the formatting
ends, the standby screen reappears.
Pressing

[No]

(

[Right Select]

) returns to the

Device Common

menu without formatting the SD card.

Display Bright. (Display brightness setting)

Sets the brightness of the message display.

In the

Device Common

menu, press





to select

Display

Bright.

Press

[OK]

. The

Display Bright.

screen appears showing the

available brightness settings.
The list shows the following brightness settings:

Darker -2
Darker -1
Normal 0
L1
L2

Press





to select the desired brightness.

Press

[OK]

. The brightness is set and the

Device Common

reappears.

Note

Formatting will destroy any existing data on a storage device including a used SD card.

Formatting of the SD card must be executed from the printer.

Format.

Are you sure?

Yes

SD Card

Display Bright.:

Darker -2

Darker -1

*Normal 0

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands