TransTel Communications G1E Plus User Manual Download Page 72

Page: 72 / 144

Program 18-nn-TK : Assign Toll Plan To Trunk Lines

18-nn-tk Toll

0000000000

nn = Toll Plan number (00-09), tk = Trunk No. (01-12)
Toll class for each trunk (class 0-9)

General:

Toll Plan allows the assignment of dialing capabilities dependent upon specific CO lines as well as individual stations.

This can be used to restrict dialing capabilities from some stations and to limit specific types of calls to certain special

purpose telephone lines.

The Toll Plans are written in Program 51 to 59 and 61 to 66.

Description:

There are total of 10 toll plans can be used.

Each Toll Plan points to a Toll Class depending on the CO line used. It is possible to allow a toll class to have different

restriction level on a line by line basis.

A station can have a Day Service toll plan and a Night Service toll plan.

Example 1: Program Mode 18-00 is set to 0000dddddd. Any station in the system which is set to toll class 0 will be

unrestricted on lines 1 to 4 but will be unable to dial out on lines 5 to 10.

Example 2: Program Mode 18-01 is set to 111100dddd. Any station in the system which is set to toll class 1 will be

restricted by toll class 1 on lines 1 to 4, will be unrestricted on lines 5 and 6 but will be unable to dial out on lines 7 and

10.

To assign toll plans to stations, see Program

41-st-05, 41-st-06

Toll Classes:

Class

Function

Prog. Mode

Unrestricted

Default

Use Mode 51 for the Unrestricted numbers. Use Mode 61 for the Restricted numbers

Mode

51,61

Use Mode 52 for the Unrestricted numbers. Use Mode 62 for the Restricted numbers

Mode

52,62

Use Mode 53 for the Unrestricted numbers. Use Mode 63 for the Restricted numbers

Mode

53,63

Use Mode 54 for the Unrestricted numbers. Use Mode 64 for the Restricted numbers

Mode

54,64

Use Mode 55 for the Unrestricted numbers. Use Mode 65 for the Restricted numbers

Mode

55,65

Use Mode 56 for the Unrestricted numbers. Use Mode 66 for the Restricted numbers

Mode

56,66

Use Mode 57 for the Unrestricted numbers.

Mode

Use Mode 58 for the Unrestricted numbers.

Mode

Use Mode 59 for the Unrestricted numbers.

Mode

Use Mode 51-56 for unrestricted numbers. Use Mode 61-66 for all restricted numbers

Cannot access the trunk line.

Summary of Contents for G1E Plus

















































































































































Search results

Summary of Contents for G1E Plus

Reviews:

Related manuals for G1E Plus

Brands by name

Popular brands

TransTel Communications G1E Plus, User Manual

Search results

Summary of Contents for G1E Plus

Reviews:

Related manuals for G1E Plus

Brands by name

Popular brands