TransTel Communications G1E Plus User Manual Download Page 25

Page: 25 / 144

Related System Program: 40-st-03

04. 12/24 Hours Clock

This parameter determines the clock display method on the LCD display of key phones.

IP \ Value

05-04-04

12 Hour Clock AM/PM

24 Hour Clock

05. SLT Hook Flash Answer Delay

This timer provides a guard time to prevent an SLT user from making an un-intended Hook Flash, such as lifting the

handset but dropping on hook again, when it tries to answer a call. The Hook Flash detection will be delayed this time

interval before activating.

IP \ Value

Unit

05-04-05

disable

sec.

06. Speed Dialing Distribution

This parameter sets the number of speed dial numbers allocated to the system or personal. The total number is 1000

sets with 100 allocated to system and 900 to personal. If name feature is enable the total number of speed dial will be

reduced to half its total. For example: if personal has 900 speed dial, when name feature is enable, its total number

will be dropped to 450. Please note that the personal speed dials are shared between all extensions. To assign the

number of personal speed for each extension refer to Mode 42-nnn-DP

IP \ Value

Value

Speed Dial Number

Personal Total / Name Feature

05-04-06

100 (100 to 199)

900/450

05-04-06

200 (100 to 299)

800/400

05-04-06

300 (100 to 399)

700/350

05-04-06

400 (100 to 499)

600/300

05-04-06

500 (100 to 599)

500/250

05-04-06

600 (100 to 699)

400/200

05-04-06

700 (100 to 799)

300/150

05-04-06

800 (100 to 899)

200/100

05-04-06

900 (100 to 999)

100/50

Note: Numbers after backslash at Personal is the total available with name feature enabled.

07. Single Digit Intercom

Single digit intercom allows the stations to call up to 5 other stations by dialing one digit only (1 to 5). This feature is for

the Hotel / Motel Environment. Up to eight different groups may be programmed. If a group is not programmed with

any entries then stations which are in the same number station group will be able to make intercom calls without

dialing the room to room dialing prefix (6).

IP \ Value

05-04-07

Disable

Enable

Summary of Contents for G1E Plus

















































































































































Search results

Summary of Contents for G1E Plus

Reviews:

Related manuals for G1E Plus

Brands by name

Popular brands

TransTel Communications G1E Plus, User Manual

Search results

Summary of Contents for G1E Plus

Reviews:

Related manuals for G1E Plus

Brands by name

Popular brands