TransTel Communications G1E Plus User Manual Download Page 23 | Manualshive

Page: 23 / 144

background image

05. Toll Access Code

It is the first dialing digit that will be checked as an effective Toll Call or not. This has no effect on toll control within the
system. It is only used to notify SMDR that a call is Toll Call or not. Refer to Program 14-01-03. Record Local Calls.
The Toll Access Code can be any one digit (0,1,2,3,4,5,6,7,8,9).

06. Station Numbering Plan

This parameter assigns the number of digits used for the station numbering plan. 2, 3, or 4 digits may be used.

IP \ Value

2

3

4

05-03-06

2 Digits

3 Digits

4 digits

07. Internal Dial Tone Pattern

System will provide different Dial tone to Analog phone when it is off hook to notifying its status. There are four
different situations which can be identified as follows:

Intercom:

Normal situation without setting to DND, CFW or MW.

DND:

Do Not Disturb.

CFWD:

Call Forwarding

MW:

Message Waiting (Some left message on the phone).

There are three different Dial Tone patterns:

Steady:

Continuous Dial Tone

2-Burst:

(Stutter Dial Tone): 250ms on / 250ms off / 250ms on / 1250ms off

3-Burst:

250ms on / 250ms off / 250ms on /250ms off / 250ms on / 750ms off

Notes:
1) If the parameter is set to 0 or 1 then the analog phone will receive the 2-Burst tone if call forward or DND has been

set for that extension.

2) Value 2 (and 6) is particularly designed for use when there is an external Voice Mail system connected to the

system, as some Voice mail units have problems with interrupted dial tone.

3) Value 6 will also provide what is known as Stutter dial tone to extensions when they are left a message. This is

useful where phones do not have a message light. When this is enabled as well as MW light to handsets by other
methods the phones with messages will receive both Message light and stutter dial tone.

IP

Value

Intercom

DND

CFWD

MW

05-03-07

0

Steady

3-Burst

3-Burst

Steady

05-03-07

1

2-Burst

3-Burst

3-Burst

2-Burst

05-03-07

2

Steady

Steady

Steady

Steady

05-03-07

3

2-Burst

2-Burst

2-Burst

2-Burst

05-03-07

4

Steady

3-Burst

3-Burst

2-Burst

05-03-07

5

2-Burst

3-Burst

3-Burst

Steady

05-03-07

6

Steady

Steady

Steady

2-Burst

05-03-07

7

2-Burst

2-Burst

2-Burst

Steady

08. Door Phone Ring Pattern

This parameter allows for different ring patterns when the Door Phone button is pressed. This Parameter will also
affect the ACP phone. If this mode is set to = 0 then the ACP will follow the extension ringing frequency otherwise it
will follow settings in this Mode. This allows stations that to distinguish a call from an ACP/Doorphone from other calls.

IP \ Value

0

1-8

9

05-03-08

Continuous ring

Same Ringing - 1 to 8 as DK handset

Background Music

(Program 05-08-08)

«
...
21
22
23
24
25
...
»

Summary of Contents for G1E Plus

















































































































































Reviews:

No comments

Related manuals for G1E Plus

Brand: Samsung Pages: 35

Brand: Samsung Pages: 7

Brand: Samsung Pages: 40

Brand: Samsung Pages: 16

Brand: Samsung Pages: 17

Admire SCH-R720

Brand: Samsung Pages: 136

A840 - SPH Cell Phone

Brand: Samsung Pages: 146

A727 - SGH Cell Phone 28 MB

Brand: Samsung Pages: 185

A660 - SPH Cell Phone

Brand: Samsung Pages: 9

A517 - SGH Cell Phone

Brand: Samsung Pages: 163

A436 - SGH Cell Phone 3 MB

Brand: Samsung Pages: 126

A437 - SGH Cell Phone

Brand: Samsung Pages: 120

A310 - SCH Cell Phone

Brand: Samsung Pages: 6

A117 - SGH Cell Phone

Brand: Samsung Pages: 92

A127 - SGH Cell Phone

Brand: Samsung Pages: 123

Byline SCH-R310 Serie

Brand: Samsung Pages: 120

Brand: Yealink Pages: 2

Brand: KALLIOPE PBX Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands