TransTel Communications G1E Plus User Manual Download Page 37

Page: 37 / 144

04. DISA Busy Tone Detection

This setting allows system to recognize busy tone from the central office line during DISA call to release the call.

Value

Value description

05-09-04

Disable

05-09-04

Australia: (420 Hz, 375ms on/off) (400 Hz, 375ms on/off)

05-09-04

Italian: (420 Hz, 500ms on/off)

05-09-04

Mexico: (420 Hz, 250ms on/off)

05-09-04

South African: (400 Hz, 500ms on/off)

05-09-04

Span: 420 Hz, 200ms on/off)

05-09-04

New Zealand: (400Hz, 250ms on/off)

05-09-04

U.S: (480 Hz + 620 Hz, 250ms on/off and 500ms on/off)

05-09-04

Indonesia: (500hz, 250ms on/off, 500ms on/off)
(420hz, 250ms on/off, 500ms on/off) (1000hz, Continuous on)

05-09-04

Israel: (450-470Hz, 700 ms on/off)

05-09-04

Pakistan

(450Hz, on:240+-40ms off:340+-40ms)

05. Reserved

06. ACD-1 Enable Time

This parameter is to set the time duration before the system answers an incoming call when the ring assigned

station(s) are busy if the operator overflow feature is enabled. The incoming call will show as a normal ring signal on

the DSS key and can be answered by the operator at any time even while the voice message is playing to the caller.

Operator Overflow (ACD-1) is enabled in Program 29-tk-02.

IP \ Value

unit

05-09-06

Sec.

07. ACD-1 Segment 2 Recall Time

This parameter sets the time an ACD-1 call which has been answered by the Overflow message will stay on hold in

the ring queue before the system will play the second part of the ACD-1 message to apologize for the continuing delay.

The call back time for the second message starts at 5 seconds and increases in 5 second increments. The message

will be played to the caller every time the recall time is reached until answered by the operator or the caller hangs up.

IP \ Value

unit

05-09-07 Disable

Sec.

08. ACD-1 Release Time

This parameter sets the time at which the system will release the incoming caller during ACD-1 operation when it has

not been answered by an operator. The system will play a warning message to the caller before releasing the call. If

polarity reversal is used for incoming call clear down then this parameter should be disabled.

IP \ Value

unit

05-09-08

Mins

Summary of Contents for G1E Plus

















































































































































Search results

Summary of Contents for G1E Plus

Reviews:

Related manuals for G1E Plus

Brands by name

Popular brands

TransTel Communications G1E Plus, User Manual

Search results

Summary of Contents for G1E Plus

Reviews:

Related manuals for G1E Plus

Brands by name

Popular brands