TransTel Communications G1E Plus User Manual Download Page 97 | Manualshive

Page: 97 / 144

background image

Program 46-stn-IP : Station Class of Service – 4

46-stn-IP STCOS
1 1 2 3 0 7 d 0

stn= Station No. (2-4 digits), IP =

Item Pointer (01-08)

Value for each Item

IP

Value

Default

Item Description

01

0-8

1= 1

Dial [87] Trunk Group

02

0-9

0= 1

Send Message Wait Signal Level

03

0-2

0= Auto Answer /MIC Off

Automatic Answer Capability / Internal CLIP

04

0-7

3= Recall

DISA/ISDN In dial Recall Capability

05

0-9

0= No Limit

Maximum Number Of Transfer Times Allowed

06

0-7

7= Yes

Door Unlock/DND/CFWD Access

07

0-9, d *

0= d

ACP Door Phone Hunt Grp./Permanent C/FW Grp.

08

0-7

0= Normal

SLT Ring Cadence Settings

General:

This program permits each station to be assigned to a different Class of Service.

Description:

01. Dial [87] Trunk Group

If this setting is from 1 to 8, after the station dials [87] (or dials [9]), the system will automatically search for a free line
which is assigned in group 1 to 8 in Program Mode 38.
If the setting is 0, then no dial 87 group is available to this station.

Related System Programming Mode:

36, 38, 41-ST-04, 46-ST-01

02. Message Waiting Level

The Stations assigned higher levels can leave message for stations with the same or lower levels. Ten levels (0-9)
are available (9=highest level, 0=lowest level). Stations which are set to 0 can not send a message waiting information
but only receive a message waiting from Stations which are class 9.

IP

Value Value Description

46-stn-02

9

Can do Message Waiting to Stations that are assigned level 0-9

46-stn-02

8

Can do Message Waiting to Stations that are assigned level 1-8

46-stn-02

n

Can do Message Waiting to Stations that are assigned level 1-n

46-stn-02

1

Only receive Message from Stations whose assigned level is > 2.

46-stn-02

0

Can not do or get Message Waiting from others.(lowest level),
except from stations assigned as level 9.

For Hotel / Lodging applications, it is recommended that you assign a message waiting level so that guest telephones
cannot leave a message for another station in the system. If you set the guest room to 1 then the room phone cannot
leave a message for another station and can ONLY get a message waiting indication from the console operator or the
voice mail system.
Message levels of the same value above 0 can leave messages for one another. Lower message levels cannot leave
messages for higher levels.
Message level 0 is special design for plain phone without Message facility.

«
...
95
96
97
98
99
...
»

Summary of Contents for G1E Plus

















































































































































Reviews:

No comments

Related manuals for G1E Plus

Brand: NEC Pages: 2

Brand: T-Mobile Pages: 4

Brand: Archos Pages: 45

Brand: AGM Pages: 11

8110 - Pearl - AT&T

Brand: Blackberry Pages: 54

Brand: Alcatel Pages: 44

Brand: Yealink Pages: 19

Brand: Snom Pages: 2

Grandstream GXP-2010

Brand: Grandstream Networks Pages: 1

ClearSky TVP-SP1BK

Brand: TRENDnet Pages: 13

Brand: Sony Ericsson Pages: 40

Brand: Olympia Pages: 31

Brand: Xiaomi Pages: 52

Brand: Haier Pages: 23

Brand: Haier Pages: 55

Brand: Haier Pages: 73

Brand: Haier Pages: 45

Brand: Huawei Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands