TransTel Communications G1E Plus User Manual Download Page 98 | Manualshive

Page: 98 / 144

background image

03. Automatic Answer Capability (Keyphone) / Internal CLI (Caller ID) Function
For Digital Key Telephone

This parameter if enabled will automatically switch on the microphone of the station if it receives an intercom call. This
setting is independent of whether the system is set to voice or ring signalling for intercom calls.

IP

Value

Value Description

46-stn-03

0

No

46-stn-03

1

MIC permanently on

46-stn-03

2

MIC will switch on for Intercom calls

For Single Line Telephone (Connected to G1E-SLU or SLT port on MBU):

This enables system to send internal and external CLI(Caller ID) signals to the single line telephone

IP

Value

Value Description

46-stn-03

0

Disable CLI sending to SLT

46-stn-03

1

Enable SDMF (number without name) CLIP sending to SLT

04. DISA/ISDN In Dial Recall Capability

This parameter affects DISA calls. When a call rings an extension but the station is busy or does not answer
(depending on setting) after the voice message announcing the status of the station is heard, the system will recall the
operator after the assigned DISA transfer time. Using the settings 1 to 3 the called station will continue to ring until the
console answers the call. Using settings 5 to 7 the call will ring the station for 1 cycle (Mode 05-08-06) and then recall
to the console and cease to ring the called station. If the parameter is set to 0 then the call will stay at the station until
answered or terminated.

IP

Value

Value Description

46-stn-04

0

No Recall to Operator

46-stn-04

1

Recall to Operator when called station is No Answer.

46-stn-04

2

Recall to Operator when called station is Busy. Camp on called station.

46-stn-04

3

Recall to Operator when called station is No Answer/Busy. Camp on called station.

46-stn-04

4

ISDN In dial calls ringing a busy station will receive busy signal.

46-stn-04

5

Recall to Operator when called station is No Answer. No Camp on function.

46-stn-04

6

Recall to Operator when called station is Busy. No Camp on function.

46-stn-04

7

Recall to Operator when called station is No Answer/Busy. No Camp on function.

46-stn-04

8

ISDN In dial calls, recall to Operator when called station is busy.

05. Maximum Re-Transferred Times

This feature allows the user or the automatic attendant console to re-transfer the same call for the number of times set
in this parameter.

IP \ Value

0

1

2

3

4

5

6

7

8

9

unit

46-stn-05

No limit

6

7

8

9

10

11

12

13

14

times

06. Door Unlock / DND / CFWD Access

This parameter allows or disallows the station from accessing the Door Unlock, Do Not Disturb (DND) and Call
Forward (CFWD) features as per the table.

IP \ Value

0

1

2

3

4

5

6

7

Door Unlock

Disallow

Allow

Disallow

Allow

Disallow

Allow

Disallow

Allow

DND

Disallow

Disallow

Allow

Allow

Disallow

Disallow

Allow

Allow

CFWD

Disallow

Disallow

Disallow

Disallow

Allow

Allow

Allow

Allow

«
...
96
97
98
99
100
...
»

Summary of Contents for G1E Plus

















































































































































Reviews:

No comments

Related manuals for G1E Plus

Brand: UniData Communication Systems Pages: 2

Brand: Alcatel Pages: 44

Yealink SIP-T20P

Brand: Yealink Pages: 2

Brand: Blackberry Pages: 30

Brand: Sagem Pages: 90

Brand: Palm Pages: 54

Brand: ALIGATOR Pages: 20

Brand: Huawei Pages: 94

Brand: Huawei Pages: 53

Brand: Huawei Pages: 12

Brand: Huawei Pages: 16

Brand: Huawei Pages: 20

Brand: Huawei Pages: 12

Brand: Huawei Pages: 20

Brand: Huawei Pages: 128

Brand: Huawei Pages: 72

Brand: Huawei Pages: 12

Brand: Huawei Pages: 133

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands