TransTel Communications G1E Plus User Manual Download Page 127

Page: 127 / 144

Program 94-tk-IP : Lunchtime Ringing And Ringing Line Preference Assignment

95-tk-IP FLX DAY
11 12 13 14 15

Tk =Trunk No. (01-12), IP=Item Pointer (01-26 )
Assigned station number

General:

This program assigns each incoming line to ring the programmed stations during Lunch Time. The ringing methods

can be:

LINEAR

(ring the first available station),

CIRCULAR

(Ring the next station following the last station who just answered an incoming call),

HUNT

(Ring the first assigned station for a set period of time (program mode 05-08-01) then if no answer ring the next

ring assigned station then the next etc.) or

COMMON AUDIBLE

(All stations will ring simultaneously).

See Program Mode: 35-tk-08 to assign.

The G1E Lunchtime ring type will follow the night ring type.

An overflow

Ring Hunt Group can be assigned to make additional stations ring after a time interval in addition to this ring

assignment. See program Mode 29-07/08. The ringing stations will be the night members programmed in mode 69.

Description:

1. This program sets Lunch Time ringing.

2. The station number can be 2,3,4 digits.

3. A total of 26 stations can be assigned to ring for each trunk.

4. If the location is to be assigned to no station, the location value is set to " 0 ".

5. To clear all entries press

[REDIAL]

6. Day and Night ring assignment are set in Mode 01 and 02.

Summary of Contents for G1E Plus

















































































































































Search results

Summary of Contents for G1E Plus

Reviews:

Related manuals for G1E Plus

Brands by name

Popular brands

TransTel Communications G1E Plus, User Manual

Search results

Summary of Contents for G1E Plus

Reviews:

Related manuals for G1E Plus

Brands by name

Popular brands