TransTel Communications G1E Plus User Manual Download Page 30 | Manualshive

Page: 30 / 144

background image

04. Polarity Reversal

This parameter is to enable the Polarity Reversal detection feature for incoming caller hang up detection in Australia
and some European countries. See Mode 14-01-08 for SMDR setting. Telecom provider needs to enable its polarity
reversal feature at the central office. When this reversal is enabled the system will hang up the CO line when the
incoming caller hangs up and the CO sends a Polarity Reversal signal to the system.

Note: 2-9 =Delay for 1-8 Seconds after accessing the line and then detect Polarity Reverse Signal

05. Operator Code

This parameter is to set whether to dial "0" or "9" for calling the operator or accessing a CO. line.

IP \ Value

0

1

05-06-05 Dial "0" for operator, "9" for C.O. line.

Dial "9" for operator, "0" for C.O. line.

06. Unsupervised Conference & ECF Time Setting

This timer defines the allows time duration on Unsupervised Conference or ECF (External Call Forward) calls. The
system will send a warning tone prior to disconnecting the call. If either party sends a DTMF digit (0-9) to the system
the timer will reset and allow the call to continue for this time setting. If reversal supervision is used, system will
release the line when reversal signal is detected.

07. Hold Feature for SLT

This parameter is to set whether Single Line Telephones use [FLASH] or [FLASH, 7] to place a call on Hold.

IP \ Value

0

1

05-06-07

Normal

Use [FLASH] to place a call on Hold.

Alternate

Use [FLASH, 7] to place a call on Hold.

08. Station Hunting Group - Ring Method:

This parameter sets the ring method used in the station hunting groups. Pilot numbers for hunt groups are set in
Program 67, Day/Night ring stations are set in Program 68 & 69, Individual Hunt Group Ring type can be set in
Program 67-gp-02 and will over ride the system wide setting made here.

IP \ Value

0

1

2

05-06-08

Common

Linear

Circular

IP \ Value

0

1

2 to 9

05-06-04

Disable

Enable

Enable after 1 to 8 seconds delay

IP \ Value

0

1

2

3

4~9

Unit

05-06-06

No Limit

1

2

3

4

Min.

«
...
28
29
30
31
32
...
»

Summary of Contents for G1E Plus

















































































































































Reviews:

No comments

Related manuals for G1E Plus

Brand: Polycom Pages: 4

blackview Crown

Brand: Iget Pages: 76

Brand: Yealink Pages: 64

Brand: Archos Pages: 45

Smartphone E-11

Brand: Etisalat Pages: 75

Brand: Polycom Pages: 2

Brand: T-Mobile Pages: 2

Brand: Doogee Pages: 8

Soundpoint IP550

Brand: Polycom Pages: 4

Brand: TAG Heuer Pages: 62

Brand: Sagem Pages: 84

Brand: T-Mobile Pages: 59

Brand: V7 Pages: 20

Brand: HP Pages: 72

Brand: Nokia Pages: 42

Brand: LG Pages: 56

Brand: LG Pages: 18

Brand: LG Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands