27
Chapter 4 How to Change Parameters with
Console Panel
This chapter describes how to change the parameters by using the console panel [SET66-Z].
r/min
Ｈｚ
Ａ
Ｖ
ＦＮＣ
ＤＩＲ
ＲＥＶ
ＡＬＭ
ＲＵＮ
ＪＯＧ
ＦＮＣ
ＲＥＳＥＴ
ＦＷＤ
ＪＯＧ
ＳＴＡＲＴ
ＳＴＯＰ
ＲＥＶ
MONI
ＳＥＴ
→
When the FNC (LED) on the console panel [SET66-Z] is turned off, press the [MONI/FNC]
key to turn on the FNC (LED).
r/min
Ｈｚ
Ａ
Ｖ
ＦＮＣ
ＤＩＲ
ＲＥＶ
ＡＬＭ
ＲＵＮ
ＪＯＧ
ＦＮＣ
ＲＥＳＥＴ
ＦＷＤ
ＪＯＧ
ＳＴＡＲＴ
ＳＴＯＰ
ＲＥＶ
MONI
ＳＥＴ
→
“0. SrEF” basic setting area is displayed. Use the [
↑
] and [
↓
] keys to
move to the desired setting item.
r/min
Ｈｚ
Ａ
Ｖ
ＦＮＣ
ＤＩＲ
ＲＥＶ
ＡＬＭ
ＲＵＮ
ＪＯＧ
ＦＮＣ
ＲＥＳＥＴ
ＦＷＤ
ＪＯＧ
ＳＴＡＲＴ
ＳＴＯＰ
ＲＥＶ
MONI
ＳＥＴ
→
Use the [JOG/
→
] key to move the operation digit to the right, and the
[FWD/REV] key to the left. Use the [
↑
] and [
↓
] keys to change the
number. After setting to the desired parameter, confirm with the [SET]
key.
<The figure on the left shows that the setting contens "b-11" is set.>
r/min
Ｈｚ
Ａ
Ｖ
ＦＮＣ
ＤＩＲ
ＲＥＶ
ＡＬＭ
ＲＵＮ
ＪＯＧ
ＦＮＣ
ＲＥＳＥＴ
ＦＷＤ
ＪＯＧ
ＳＴＡＲＴ
ＳＴＯＰ
ＲＥＶ
MONI
ＳＥＴ
→
Use the [
↑
] and [
↓
] keys to change to a desired number, and press the
[SET] key to confirm.
<The figure on the left shows that the parameter data is set to “1.”>
r/min
Ｈｚ
Ａ
Ｖ
ＦＮＣ
ＤＩＲ
ＲＥＶ
ＡＬＭ
ＲＵＮ
ＪＯＧ
ＦＮＣ
ＲＥＳＥＴ
ＦＷＤ
ＪＯＧ
ＳＴＡＲＴ
ＳＴＯＰ
ＲＥＶ
MONI
ＳＥＴ
→
The changed parameter is displayed again
<The figure on the left shows “b-11” because the setting item
“b-11” is set.>
Press the [MONI/FNC] key to turn off FNC (LED). Monitor item, such as
“SPd,” is displayed for about one second. Data of the monitor item is
displayed.
r/min
Ｈｚ
Ａ
Ｖ
ＦＮＣ
ＤＩＲ
ＲＥＶ
ＡＬＭ
ＲＵＮ
ＪＯＧ
ＦＮＣ
ＲＥＳＥＴ
ＦＷＤ
ＪＯＧ
ＳＴＡＲＴ
ＳＴＯＰ
ＲＥＶ
MONI
ＳＥＴ
→
r/min
Ｈｚ
Ａ
Ｖ
ＦＮＣ
ＤＩＲ
ＲＥＶ
ＡＬＭ
ＲＵＮ
ＪＯＧ
ＦＮＣ
ＲＥＳＥＴ
ＦＷＤ
ＪＯＧ
ＳＴＡＲＴ
ＳＴＯＰ
ＲＥＶ
MONI
ＳＥＴ
→
As to the Areas A to S, while the alphabet part is blinking, you can move
to other setting areas.
*For parameters, refer to “Chapter 6 List of Parameters” and “Chapter 7 Description of Parameters.”
*For the setting area, refer to “Chapter 5 List of Setting Areas.”
*For the setting areas, refer to “Chapter 5 List of Setting Areas.”
In case of selection data, use the
[
↑
] and [
↓
] keys to select the data.
In case of selection data
If the data cannot be written
If the selected parameter
does not exist
Less than the lower
limit of the setting
More than the upper
limit of the setting
Rewrite prohibited
