Thermo Scientific GENESYS 10S Vis User Manual Download Page 35

Page: 35 / 134

Thermo Scientific

GENESYS 10S Vis User Guide

Cell Correction

Every test setup screen provides access to Cell Correction.

Before running Cell Correction:

• Clean the inside and outside of all the cells to be matched.

• Fill the cells with distilled water (or other blank solution), and place them in the sample

compartment (see

“Selecting and Positioning Cuvettes”

page 5

). Place the blank

cuvette in Cell “B” of the cell changer.

Cell Correction

To run Cell Correction

1. Load the test type or stored test.

2. If Cell Correction is not visible, highlight

More parameters

and press

Enter

Note

Cell Correction is not active from the Main (Basic ATC) screen.

Note

Cell Correction is active only when the 6-Position Cell Holder is set to either Auto

6 or Auto 3. The feature is not active when the cell holder is set to 1-Cell or Manual 6, nor
when the Single Cell Holder is installed.

Summary of Contents for GENESYS 10S Vis







































































































































Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands

Thermo Scientific GENESYS 10S Vis, User Manual

Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands