Thermo Scientific GENESYS 10S Vis User Manual Download Page 101

Page: 101 / 134

Kinetics

Measuring Samples

Thermo Scientific

GENESYS 10S Vis User Guide

2. When the parameters are set, press

Save Test

to save the test or

Run Test

to measure a

blank or sample.

Measuring Samples

To measure samples

1. In the Kinetics screen, press

Run Test

2. If a 6-Position Cell Holder is installed, place the blank in position B and the sample in

position #1.

3. Press

Measure Sample

Parameter

Description

Delay Time

Enters the time from Test Initiation to first measurement; allows for
sample equilibration
Adv.

Interval Time

Enters the time between repeated readings

Measure Blank
(as function key)

Selects the frequency of zeroing the instrument

Once or Every Reading

Note

If Cell Correction is ON, you must run the Setup Correction application before

you can access Run Test or Measure Samples.

Note

If Auto Save Data is ON, you must enter a Data File Name before you can

access Run Test or Measure Samples.

Note

If a 6-Postion Cell Changer is installed, place the blank in position B and the sample

in cell position #1. The instrument always uses cell position #1 to scan the sample.

Summary of Contents for GENESYS 10S Vis







































































































































Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands

Thermo Scientific GENESYS 10S Vis, User Manual

Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands