Thermo Scientific GENESYS 10S Vis User Manual Download Page 97

Page: 97 / 134

Concentration Measurements—Standard Curve Application

Editing a Standard Curve

Thermo Scientific

GENESYS 10S Vis User Guide

All absorbance measurements are removed from the screen.

To reset standards

1. With the standard curve displayed, press

Edit Standards

2. Highlight

Reset Standards

and press

Enter

All standards and measurements are removed from the screen.

To select a different curve fit for a standard curve

1. With the standard curve you want to edit displayed as a graph, press

Change Fit

2. Highlight the curve fit to use for the standard curve and press

Enter

The instrument applies the selected curve fit to the data and displays the new fit.

Note

To change the curve fit for a standard curve, you must display the standard curve as

a graph, not as a table.

Summary of Contents for GENESYS 10S Vis







































































































































Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands

Thermo Scientific GENESYS 10S Vis, User Manual

Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands