Thermo Scientific GENESYS 10S Vis User Manual Download Page 28

Page: 28 / 134

Accessories

Cell Holders and Cell Holder Accessories

GENESYS 10S Vis User Guide

Thermo Scientific

Figure 2.

Single Cell Holder

3. With your other hand, tighten the captive thumbscrew(s).

4. Close the sample compartment door.

Removing the 6-Position Cell Holder and the Single Cell Holder

To remove the 6-Position Cell Holder and the Single Cell Holder

1. Open the sample compartment door and let it rest on its hinge.

2. With one hand, loosen the captive thumbscrew.

3. With your other hand, pull straight up on the cell holder and lift it out of the sample

compartment

4. Close the sample compartment door.

Installing Accessory Cell Holders

Make sure that you have the correct cell holder baseplate installed.

Note

If the cell holder is not aligned correctly, you will not be able to tighten the

thumbscrews.

Captive thumbscrews

Single cell holder

Alignment pin hole

Summary of Contents for GENESYS 10S Vis







































































































































Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands

Thermo Scientific GENESYS 10S Vis, User Manual

Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands