Thermo Scientific GENESYS 10S Vis User Manual Download Page 114

Page: 114 / 134

Performance Verification

Noise

106

GENESYS 10S Vis User Guide

Thermo Scientific

If the test fails, follow these guidelines:

• Repeat the test twice to verify that the test is failing consistently.

• Follow the guidelines provided with the standard reference materials.

• For more troubleshooting advice contact our sales or service representative in your area or

use the information at the beginning of this document to contact us.

Noise

This test measures the amount of noise at 340 nm.

All test parameters are determined by instrument specifications and cannot be changed by the
user. When running the noise test, remember:

• Perform the 0A measurement with the cell holder empty. Optionally you can perform the

2A measurement with a 2A filter.

To run the Noise Measurement test

1. Highlight

Noise Measurement

2. Press

Enter

3. With the Blank position empty, insert the 2A filter in position #1.

Ignore the test results at 2A if you do not have a filter installed in position #1.

4. Press

Start Test

The results of the test indicate pass or fail for each wavelength.

If the test fails, follow these guidelines:

• Repeat the test twice to verify that the test is failing consistently.

Summary of Contents for GENESYS 10S Vis







































































































































Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands

Thermo Scientific GENESYS 10S Vis, User Manual

Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands