Thermo Scientific GENESYS 10S Vis User Manual Download Page 18

Page: 18 / 134

Setting Up the Instrument

Setting Utility Parameters

GENESYS 10S Vis User Guide

Thermo Scientific

2. Press

Set Date

, type the date and press

Enter

3. Press

Set Month

, highlight the correct month and press

Enter

4. Press

Set Year

, type the year and then

Enter

5. Press

Esc

to save the settings.

To select the time format

You can set the instrument to display the time in either am/pm or 24-hour format. To change
the format, highlight

Time Format

and press

Enter

until the desired format (AM/PM or 24

hour) appears.

To set the time

1. Highlight

Set Time

and press

Enter

2. To set the hour, press

Set Hour

, type in the hour and press

Enter

3. To set the minutes, press

Set Minute

, type in the minute and press

Enter

4. To select between AM and PM (if in AM/PM time format), press

Set AM/PM

until the

appropriate setting appears.

Since the tungsten lamp of the GENESYS 10S Vis spectrophotometer requires a 30-minute
warm-up, the spectrophotometer has been pre-set at the factory to Standby Mode OFF.

To change Standby Mode time

1. Highlight

Standby

and press

Enter

2. Highlight the length of time you want the instrument to wait before entering standby

mode and press

Enter

Note

Your changes are saved automatically (even during power down) by battery

backup.

Summary of Contents for GENESYS 10S Vis







































































































































Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands

Thermo Scientific GENESYS 10S Vis, User Manual

Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands