Thermo Scientific GENESYS 10S Vis User Manual Download Page 17

Page: 17 / 134

Setting Up the Instrument

Setting Utility Parameters

Thermo Scientific

GENESYS 10S Vis User Guide

Setting Utility Parameters

The Utility menu lets you set certain non-test hardware parameters, such as the date and time,
standby setting, screen contrast settings and printer setup. You can also access a directory of all
stored tests and the calculator function.

You cannot set utility parameters or change the utility when the instrument is carrying out a
measurement.

• Press

Utility

on the keypad.

Setting the Date and Time

Highlight

Date/Time Setup

and press

Enter

You can modify the date, time format and time.

To set the date

1. Highlight

Set Date

and press

Enter

Summary of Contents for GENESYS 10S Vis







































































































































Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands

Thermo Scientific GENESYS 10S Vis, User Manual

Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands