Terex Genie Z-40 Service And Repair Manual Download Page 42

Page: 42 / 287

Service and Repair Manual

June 2022

Platform Components

-62/40

Part No. 1268555GT

2-2 Plat for m Rot ato r

2-2

Platform Rotator

How to Remove the Platform

Rotator

Component damage hazard.

Mark the platform mounting

weldment and the rotator flange

before removing the platform

mounting weldment. The

platform mounting weldment

must be replaced in the exact

same position on the rotator

flange as it was before removal.

If a new rotator is installed or

the rotator is disassembled,

proper alignment can be

achieved by rotating the rotator

all the way to the left and then

installing the platform mounting

weldment all the way in the left

position.

Note: When removing a hose assembly or fitting,

the O-ring (if equipped) on the fitting and/or hose

end must be replaced. All connections must be

torqued to specification during installation. Refer to

Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1 Remove the platform and platform support.
2 Tag, disconnect and plug the hydraulic hoses

from the platform rotator manifold. Cap the

fittings on the rotator.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

3 Support the platform rotator with an

appropriate lifting device. Do not apply any

lifting pressure.

Crushing hazard. The platform

rotator could fall when removed

from the machine if not properly

supported.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands