Terex Genie Z-40 Service And Repair Manual Download Page 124

Page: 124 / 287

Service and Repair Manual

June 2022

Deutz TD 2.2 L3 Engine Fault Codes

110

-62/40

Part No. 1268555GT

DTC = Diagnostic Trouble Code
FMI = Failure Mode Identifier

SPN = Suspect Parameter Number

DTC SPN

FMI Description

877 5441

Engine fuel injection timing error

for multiple cylinders.

878 5357

Engine fuel injection error for

multiple cylinders. Diagnostic

fault check to report the error

due to non plausibility in ZFC.

879 523612 12

Internal recovery. Diagnosis fault

check to report the error to

demand for an ICO due to an

error in the PoI2 shut-off.

598

Clutch switch. Abnormal rate of

change.

880 523612 12

Internal recovery. Diagnosis fault

check to report the error to

demand for an ICO due to an

error in the PoI3 efficiency factor.

881 523612 12

Internal recovery. Diagnosis fault

check to report the error to

demand for an ICO due to an

error in change of EOM.

882 5357

Engine fuel injection error for

multiple cylinders. Diagnosis

fault check to report the error to

demand for an ICO due to an

error in total torque relevant

quantity.

883 5357

Engine fuel injection error for

multiple cylinders. Diagnostic

fault check to report the error

due to injection quantity

correction.

884 5442

Engine fuel injection pressure

error for multiple cylinders.

885 29

Accelerator pedal 2 position.

886 677

Engine starter motor relay.

Function monitoring: Fault of

ECU power train active.

DTC SPN

FMI Description

887 513

Actual engine percent torque.

DFC to report the fault in

energizing time comparison.

888 513

Actual engine percent torque.

DFC to report in torque

comparison error.

889 520250 2

Function monitoring: Error in the

post-build selectable monitoring.

890 629

ECU. Status of the EMM alarm

FCCU0 which is read out of the

FCCU hardware module.

1109

Engine protection system

approaching shutdown. Engine

shut off demand ignored.

1109

Engine protection system

approaching shutdown. Shut off

request from supervisory

monitoring function.

996 629

ECU. Diagnostic fault check to

report ABE active state.

997 629

Function monitoring: Fault of

ECU, WDA active by

inquiry/response communication.

998 629

Function monitoring: Fault of

ECU, Error Pin active suspision

of HW fault.

999 629

Function monitoring: Fault of

ECU, WDA active by overvoltage

detection.

The following DTC fault code range shares the same

description. Replace the ECU.
DTC

891 - 945

Description

SPN

629

Internal ECU error.

FMI

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands