Terex Genie Z-40 Service And Repair Manual Download Page 47

Page: 47 / 287

June 2022

Service and Repair Manual

Jib Boom Components

Part No. 1268555GT

-62/40

3-2 Ji b Boo m Lift C ylinde r

3-2

Jib Boom Lift Cylinder

How to Remove the Jib Boom Lift

Cylinder

Note: Perform this procedure with the boom in the

stowed position.
Note: When removing a hose assembly or fitting,

the O-ring (if equipped) on the fitting and/or hose

end must be replaced. All connections must be

torqued to specification during installation. Refer to

Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1 Raise the jib boom slightly and place blocks

under the platform support. Lower the jib

boom until the platform is resting on the

blocks just enough to support the platform.

Note: Do not rest the entire weight of the boom on

the blocks.
2 Tag, disconnect and plug the jib boom lift

cylinder hydraulic hoses. Cap the fittings on

the cylinder.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

3 Remove the pin retaining fasteners from the

jib boom lift cylinder rod-end pivot pin. Do not

remove the pin.

4 Use a soft metal drift to tap the jib boom lift

cylinder rod-end pivot pin out enough to lower

one of the leveling arms to the ground. Tap

the pin the other direction and lower the

opposite leveling arm. Do not remove the pin.

5 Support the jib boom lift cylinder with a

suitable lifting device.

6 Remove the pin retaining fastener from the jib

boom lift cylinder barrel-end pivot pin. Use a

soft metal drift to remove the barrel-end pin

and let the cylinder hang down.

Crushing hazard. The jib boom

may become unbalanced and

fall when it is removed from the

machine if it is not properly

supported by the overhead lifting

device.

7 Attach a lifting strap from an overhead crane

to the lug on the rod end of the jib boom lift

cylinder.

8 Use a soft metal drift to remove the jib boom

lift cylinder rod-end pin. Remove the jib boom

lift cylinder from the machine.

Crushing hazard. The jib boom

lift cylinder may become

unbalanced and fall when it is

removed from the machine if it is

not properly supported by the

lifting device.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands