Terex Genie Z-40 Service And Repair Manual Download

Page: 39 / 287

June 2022

Service and Repair Manual

Platform Controls

Part No. 1268555GT

-62/40

10 Compare the function ramp rate time with the

table below and determine whether the ramp

rate time needs to increase or decrease.

11 While the joystick is activated, set the ramp

rate. Momentarily move the drive enable

toggle switch in the right direction to increase

the time or momentarily move the drive

enable toggle switch in the left direction to

decrease the time.

Note: Each time the drive enable toggle switch is

momentarily moved, the time will change in 5%

increments.
12 Repeat steps 9 through 11 for each joystick

controlled machine function.

13 Return the joystick to the neutral position and

wait for approximately 10 seconds to allow the

settings to be saved.

Result: The alarm should sound indicating

that the settings have been saved in memory.

Note: Do not operate any machine function during

the 10 second waiting time.

Ramp rate (factory settings)

Primary boom up/down

accelerate

3 seconds

decelerate

1 second

Secondary boom up/down

accelerate

2 seconds

decelerate

1 second

Turntable rotate

accelerate

2 seconds

decelerate

0.5 second

Drive

accelerate

2 seconds

decelerate to neutral

0.5 second

decelerate, change of direction

0.5 second

decelerate, coasting

0.75 second

decelerate, braking

1.5 seconds

decelerate, shift from low to high

speed

1.75 seconds

decelerate, shift from high to low

speed - 2WD models

1 second

decelerate, shift from high to low

speed - 4WD models

3.5 seconds

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands