manualshive.com logo in svg

Terex Genie Z-40, Service And Repair Manual, Page: 94 / 287

Share
Download
Terex Genie Z-40 Service And Repair Manual Download Page 94

Service and Repair Manual

 

June 2022

 

Turntable Rotation Components 

 

 

80 

Z

®

-62/40

 

Part No. 1268555GT 

 

 

Turnta ble R ota tion C ompone nt s  

9-1  Tur nta ble Rot ation  Assem bly  

9-1 

Turntable Rotation Assembly 

How to Remove the Turntable 

Rotation Assembly 

Note: When removing a hose assembly or fitting, 

the O-ring (if equipped) on the fitting and/or hose 

end must be replaced. All connections must be 

torqued to specification during installation. Refer to 

Specifications, 

Hydraulic Hose and Fitting Torque 

Specifications.

 

Note: Perform this procedure with the machine on 

a firm, level surface. 
1  Start the machine and rotate the boom 90° to 

either side of the drive chassis. 

2  Loosen the retaining fasteners securing the 

turntable rotation gear backlash plate. 

Note: Do not loosen the jam nut securing the 

backlash adjustment bolt. 

 

1  jam nut 
2  adjustment bolt 
3  pivot plate retaining fasteners 

 

 

3  Start the machine and rotate the boom back 

to the stowed position. 

4  Secure the turntable from rotating with the 

turntable rotation lock. 

 

Tip-over hazard. The machine 

could tip over when the turntable 

rotation assembly is removed if 

the turntable rotation lock is not 

in the locked position. 

5  Raise the secondary boom until the upper 

pivot is 6 feet / 2 m above the counterweight. 

6  Install a cylinder chock (Genie part number 

33484) onto the secondary lift cylinder rod. 

Lower the secondary just until the chock 

makes contact with the barrel of the lift 

cylinder. 

Note: Do not apply all the weight of the secondary 

boom on the chock. 
7  Loosen the jam nut securing the backlash 

adjustment bolt. Turn the adjustment bolt 

counter-clockwise until the turntable rotation 

assembly can move freely. 

8  Tag, disconnect and plug the hydraulic hoses 

from the turntable rotation motor manifold. 

Cap the fittings on the manifold. 

 

Bodily injury hazard. Spraying 

hydraulic oil can penetrate and 

burn skin. Loosen hydraulic 

connections very slowly to allow 

the oil pressure to dissipate 

gradually. Do not allow oil to 

squirt or spray. 

9  Remove the turntable rotation assembly 

mounting fasteners. 

Summary of Contents for Genie Z-40
































































































































































































































































































Reviews:

No comments