manualshive.com logo in svg

Terex Genie Z-40, Service And Repair Manual, Page: 103 / 287

Share
Download
Terex Genie Z-40 Service And Repair Manual Download Page 103

June 2022

 

Service and Repair Manual

 

 

Control System Fault Codes

 

 

 

Part No. 1268555GT

 

Z

®

-62/40

 

89 

 

 

Contr ol Sys tem Fault C ode s  

How to Re triev e Con trol Syst em  Fa ult Cod es  

Control System 

How to Retrieve Control System 

Fault Codes 

At least one fault code is present when the alarm 

at the platform controls produces two short beeps 

every 30 seconds for 10 minutes. 
Perform this procedure with the engine off, the key 

switch turned to platform controls and the red 

Emergency Stop button pulled out to the on 

position at both the ground and platform controls.   
1  Open the platform control box lid. 

 

Electrocution/burn hazard. 

Contact with electrically charged 

circuits could result in death or 

serious injury. Remove all rings, 

watches and other jewelry. 

2  Locate the red and yellow fault LEDs on the 

ALC-500 circuit board inside the platform 

control box. Do not touch the circuit board. 

 

Component damage hazard. 

Electrostatic discharge (ESD) 

can damage printed circuit board 

components. Maintain firm 

contact with a metal part of the 

machine that is grounded at all 

times when handling printed 

circuit boards OR use a 

grounded wrist strap. 

 

 

3 

Determine the error source:

 The red LED 

indicates the error source and will flash two 

separate codes. The first code will indicate 

the first digit of the two digit code, flashing 

once per second. It will then pause for 

1.5 seconds and flash the second digit once 

per 0.5 second. 

Note: When the red LED is flashing the code, the 

yellow LED will be on solid. 
4 

Determine the error type:

 The yellow LED 

indicates the error type and will flash two 

separate codes. The first code will indicate 

the first digit of the two digit code, flashing 

once per second. It will then pause for 

1.5 seconds and flash the second digit once 

per 0.5 second. 

Note: When the yellow LED is flashing the code, 

the red LED will be on solid. 
5  Use the fault code table on the following 

pages to aid in troubleshooting the machine 

by pinpointing the area or component 

affected. 

 

Summary of Contents for Genie Z-40
































































































































































































































































































Reviews:

No comments