Terex Genie Z-40 Service And Repair Manual Download

Page: 116 / 287

Service and Repair Manual

June 2022

Deutz TD 2.2 L3 Engine Fault Codes

102

-62/40

Part No. 1268555GT

DTC = Diagnostic Trouble Code
FMI = Failure Mode Identifier

SPN = Suspect Parameter Number

DTC SPN FMI Description

111 102 0

Engine intake manifold pressure

above normal operational range.

1114 102 1

Engine intake manifold pressure

below normal operational range.

1115 102 3

Intake manifold pressure sensor

voltage above normal or shorted to

high.

1116 102 4

Intake manifold pressure sensor

voltage below normal or shorted to

low.

1118 102 1

Intake manifold pressure below

normal operational range.

1121 102 2

DFC for signal variation check for

pressure sensor of the intake

manifold.

1122 102 0

Intake air pressure valve sensor,

warning condition exceeded.

1123 102 1

Intake air pressure valve sensor,

shutoff condition exceeded.

1124 1209 2

Engine exhaust pressure turbine

upstream differs from ambient

pressure while engine not running.

1125 1209 15

Engine exhaust pressure turbine

upstream above upper limit.

1126 1176 1

Engine turbocharger compressor

intake pressure below normal

operational range.

1127 1209 2

Engine exhaust pressure turbine

upstream tuck check failed.

Pressure does not change

between engine operating points.

1130 1209 3

Engine exhaust pressure sensor

voltage above normal or shorted to

high.

1131 1209 4

Engine exhaust pressure sensor

voltage below normal or shorted to

low.

DTC SPN FMI Description

1134 3251 3

DPF voltage above normal or

shorted to high.

1135 3251 4

DPF voltage below normal or

shorted to low.

1136 3251 14

DPF reporting communication

error.

1137 3251 14

DPF reporting data error.

1138 3251 14

DPF reporting fast channel 1 error.

1139 3251 14

DPF reporting fast channel 2 signal

range error.

1149 3251 2

DPF difference pressure value not

plausible.

1150 3251 0

DPF difference pressure above

shut off threshold.

1151 3251 16

DPF difference pressure above

warning threshold.

1152 3251 1

DPF difference pressure below

shut off threshold.

1153 3251 18

DPF difference pressure below

warning threshold.

1161 5571 16

Rail fuel pressure relief valve

above normal operational range.

1162 5571 2

Rail fuel pressure relief valve is

forced to open, perform pressure

increase.

1163 5571 2

Rail fuel pressure relief valve is

forced to open. Performed by

pressure increase.

1164 5571 16

Rail fuel pressure relief valve is

forced to open. Shutoff conditions.

1165 5571 15

Rail fuel pressure relief valve is

forced to open. Warning

conditions.

1166 5571 0

Open rail fuel pressure relief valve

was detected.

1167 5571 2

Unexpected opening of the rail fuel

pressure relief valve.

1168 5571 2

Successful rail fuel pressure relief

valve opening cannot be ensured.

1169 5571 13

Averaged rail fuel pressure after

valve opening is outside the

expected tolerance range.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands