Terex Genie Z-40 Service And Repair Manual Download Page 33

Page: 33 / 287

June 2022

Service and Repair Manual

Repair Procedures

Part No. 1268555GT

-62/40

Secti on 3

Repair P roce dur es

Intro ductio n

Observe and Obey:



Repair procedures shall be completed by a

person trained and qualified on the repair of

this machine.



Immediately tag and remove from service a

damaged or malfunctioning machine.



Repair any machine damage or malfunction

before operating the machine.

Before Repairs Start:



Read, understand and obey the safety rules

and operating instructions in the appropriate

operator's manual on your machine.



Be sure that all necessary tools and parts are

available and ready for use.



Use only Genie approved replacement parts.



Read each procedure completely and adhere

to the instructions. Attempting shortcuts may

produce hazardous conditions.

Machine Configuration:



Unless otherwise specified, perform each

repair procedure with the machine in the

following configuration:

•

Machine parked on a firm, level surface

•

Key switch in the off position with the key

removed

•

The red Emergency Stop button in the off

position at both the ground and platform

controls

•

Wheels chocked

•

All external AC power supply disconnected

from the machine

•

Boom in the stowed position

•

Turntable secured with the turntable rotation

lock

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands