Terex Genie Z-40 Service And Repair Manual Download Page 45

Page: 45 / 287

June 2022

Service and Repair Manual

Platform Components

Part No. 1268555GT

-62/40

5 Move the platform up and down by hand, so it

bounces approximately 2.5 to 5 cm / 1 to

2 inches. Allow the platform to settle.

Result: The overload indicator lights are off

and the alarm does not sound. Proceed to

step 6.

Result: The overload indicator lights are

flashing at the platform and ground controls,

and the alarm is sounding. Slowly tighten the

load spring adjustment nut in a clockwise

direction in 10° increments until the overload

indicator light turns off, and the alarm does

not sound. Repeat step 5.

Note: The platform will need to be moved up and

down and allowed to settle between each

adjustment.
Note: There may be a 2 second delay before the

platform overload indicator light and alarm

responds.
6 Turn the key switch to ground controls, pull

out the red Emergency Stop Button and start

the engine.

7 Add an additional weight to the platform that

is equal to, but does not exceed 15% of the

maximum rated load.

Result: The overload indicator light is flashing

at both the ground and platform controls, the

alarm is sounding and the engine shuts down.

Proceed to step 8.

Result: The overload indicator lights are off at

the platform and ground controls, the alarm

does not sound and the engine continues to

run. Slowly loosen the load spring adjustment

nut in a counterclockwise direction in 10°

increments until the overload indicator light

flashes at both the platform and ground

controls, the alarm sounds and the engine

shuts down. Remove the additional weight.

Repeat the procedure starting with step 5.

Note: There may be a 2 second delay before the

platform overload indicator light and alarm

responds.
8 Using auxiliary power, test all machine

functions from the ground controls.

Result: All ground control functions should

operate.

9 Using a suitable lifting device, remove the

additional weight from the platform.

Result: The platform overload indicator light

should be off at both the ground and platform

controls and the alarm should not sound.

Note: There may be a 2 second delay before the

overload indicator lights and alarm turn off.
10 Start the engine and test all machine

functions from the ground controls.

Result: All ground control functions should

operate.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands