manualshive.com logo in svg

Terex Genie Z-40, Service And Repair Manual, Page: 56 / 287

Share
Download
Terex Genie Z-40 Service And Repair Manual Download Page 56

Service and Repair Manual

 

June 2022

 

Secondary Boom Components 

 

 

42 

Z

®

-62/40

 

Part No. 1268555GT 

 

 

9  Remove the pin retaining fastener securing 

the rod-end pivot pin of the secondary boom 

lift cylinder. Remove the pivot pin securing the 

lift cylinder. 

10  Lift and move the cylinder towards the center 

of the machine enough to lower it down 

through the lower compression arm. Pull the 

cylinder towards the platform and remove it 

from the machine. 

 

Crushing hazard. The secondary 

boom lift cylinder could become 

unbalanced and fall when 

removed from the machine if not 

properly attached to the suitable 

lifting device. 

 

 

 

Component damage hazard. 

When removing a secondary 

boom lift cylinder from the 

machine, be careful not to 

damage the counterbalance 

valve at the barrel end of the 

cylinder. 

 

 

Summary of Contents for Genie Z-40
































































































































































































































































































Reviews:

No comments