Terex Genie Z-40 Service And Repair Manual Download | Manualshive

Page: 115 / 287

background image

June 2022

Service and Repair Manual

Deutz TD 2.2 L3 Engine Fault Codes

Part No. 1268555GT

Z

®

-62/40

101

Deutz TD 2.2 L3 E ngi ne Fa ult C odes

DTC = Diagnostic Trouble Code
FMI = Failure Mode Identifier
SPN = Suspect Parameter Number

DTC SPN FMI Description

1000 98

2

Engine oil level sensor internal

error. Sensor reports error.

Open/short transducer.

1001 98

31

Engine oil level out of range. Level

low, high, foaming.

1002 98

31

Oil sensor voltage out of range.

<8,5V ±0,5V; >16,5V ±0,5V.

1003 98

2

Oil sensor invalid sensor status.

1004 98

31

Oil sensor temperature out of

range.

1005 98

14

Oil sensor is broken or

disconnected.

1021 100 3

Oil pressure voltage above normal

or shorted to high.

1022 100 4

Oil pressure voltage below normal

or shorted to low.

1025 100 1

Low oil pressure. Warning

threshold exceeded.

1026 100 1

Low oil pressure. Shut off threshold

exceeded.

1043 107 0

Air filter differential pressure. Air

filter clogged.

1071 411 2

Engine exhaust gas recirculation.

Pressure does not change

between engine operating points.

1072 411 0

Engine exhaust gas recirculation.

Pressure above normal operational

range.

1073 411 1

Engine exhaust gas recirculation.

Pressure below normal operational

range.

1074 411 2

Engine exhaust gas recirculation.

Negative measured differential

pressure.

1075 411 2

Engine exhaust gas recirculation.

Positive measured differential

pressure.

DTC SPN FMI Description

1077 411

3

Engine exhaust gas recirculation.

Signal value above maximum limit.

1078 411

4

Engine exhaust gas recirculation.

Signal value below maximum limit.

1079 108

0

Ambient air pressure sensor above

normal operational range.

1080 108

1

Ambient air pressure sensor below

normal operational range.

1081 108

15 Fault check max signal range

violated for ambient air pressure

sensor.

1082 108

17 Fault check min signal range

violated for ambient air pressure

sensor.

1083 108

2

Ambient air pressure sensor error

by component self diagnosis.

1084 3720 0

DPF ash load above normal

operational range.

1086 3734 0

DPF soot load exceeded. Remove

filter level.

1087 4781 14 DPF soot load exceeded shut off

level.

1088 4781 0

DPF soot load exceeded warning

level.

1089 4781 16 DPF. Too much standstill time in

short time interval.

1090 10156 0

DPF. The standstill-regeneration

mode time exceeds the short-limit.

1091 3735 16 DPF. Standstill required and no

successful standstill longer than

escalation threshold. Moderately

severe.

1092 3735 0

DPF. Standstill required and no

successful standstill longer than

escalation threshold. Most severe.

1093 4766 1

DOC. Regeneration temperature in

standstill main phase not reached.

1102 171

2

Ambient air temperature shows a

deviation from expected value at

cold start conditions.

«
...
113
114
115
116
117
...
»

Summary of Contents for Genie Z-40
































































































































































































































































































Reviews:

No comments

Related manuals for Genie Z-40

Brand: Terex Pages: 78

Brand: Genie Pages: 35

Brand: Genie Pages: 46

Brand: Genie Pages: 50

Brand: Genie Pages: 63

Brand: Genie Pages: 64

Brand: Genie Pages: 69

Brand: Genie Pages: 123

Brand: Genie Pages: 144

Brand: Genie Pages: 169

Brand: Genie Pages: 305

Brand: Genie Pages: 353

Brand: Genie Pages: 440

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands