Terex Genie Z-40 Service And Repair Manual Download Page 66

Page: 66 / 287

Service and Repair Manual

June 2022

Hydraulic Pumps

-62/40

Part No. 1268555GT

5 Carefully pull the drive pump out until the

pump coupler separates from the flex plate.

6 Remove the drive pump from the machine.

Component damage hazard. The

pump(s) may become

unbalanced and fall if not

properly supported.

Component damage hazard.

When installing the pump, do not

force the pump coupler into the

flexplate or damage to the pump

shaft seal may occur.

Component damage hazard. Be

sure to open the two hydraulic

tank valves and prime the pump

after installing the pump.

How to Prime the Drive Pump

1 Connect a 0 to 600 psi / 0 to 41 bar pressure

gauge to the test port on the drive pump.

Ford models:

Close the valve on the LPG

tank then disconnect the hose from the tank.

Then move the fuel select switch to the LPG

position.

Perkins 404D-22 models:

Disconnect the

engine wiring harness from the fuel solenoid

at the injector pump.

Deutz D2011 L03i models:

Hold the manual

fuel shutoff valve clockwise to the closed

position.

1 manual fuel shutoff valve

3 Have another person crank the engine with

the starter motor for 15 seconds, wait

15 seconds, then crank the engine an

additional 15 seconds or until the pressure

reaches 310 psi / 21 bar.

Ford models:

Connect the LPG hose to the

LPG tank and open the valve on the tank.

Perkins 404D-22 models:

Connect the

engine wiring harness to the fuel solenoid.

Deutz D2011 L03i models:

Release the

manual fuel shutoff valve.

5 Start the engine from the ground controls and

check for hydraulic leaks.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Terex Genie Z-40, Service And Repair Manual, Page: 66 / 287

Search results

Summary of Contents for Genie Z-40

Reviews: