Terex Genie Z-40 Service And Repair Manual Download Page 100

Page: 100 / 287

Service and Repair Manual

June 2022

Track Components

-62/40

Part No. 1268555GT

21 Continue to pump grease into the cylinder

until the track has proper tension.

Component damage hazard.

Do not over tighten the track.

Over tightening the track will

cause the machine to lose

power during operation.

Note: If the track becomes too tight, loosen the

grease plug on the cylinder to remove grease and

loosen the track.
22 Raise the machine, remove the jack stands

and lower the machine.

23 Drive the machine in either direction just until

the remaining sprocket retaining fasteners

can be installed onto the drive hub adapter.

Turn the machine off.

24 Install the remaining sprocket retaining

fasteners to the drive hub adapter and torque

to specification. Refer to Specifications,

TraX

Torque Specifications

Grease Specification

Chevron Ultra-duty grease, EP NLGI 1 (lithium based)

or equivalent

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands