Terex Genie Z-40 Service And Repair Manual Download Page 105

Page: 105 / 287

June 2022

Service and Repair Manual

Control System Fault Codes

Part No. 1268555GT

-62/40

Error Source

Error Type

Condition

Solution

ID Name

Name

32 Secondary Up /

Down. Directional

Valves

Fault

Limited Speed and Direction frozen at

zero and neutral, Alarm sounds.

Power up controller with

problem corrected.

33 Secondary Up /

Down Flow Valve

Value too high Limited Speed and Direction frozen at

zero and neutral, Alarm sounds.

Power up controller with

problem corrected.

Value too low

Not Calibrated Normal function except threshold for

one or both directions is zero.

Calibrate valve threshold.

Just calibrated Initiate 1 second beep of Alarm.

Self-clearing (transient)

34 primary Boom

Extend / Retract

Limit Switches

Invalid setup

Initiate 1 second beep of Alarm.
1000lb. Mode: Required retract into

FULLY RETRACTED state before

lowering.

500lb. Mode: Operates normally.
Dual capacity models.

Fully retract, then lower

boom.

Check and service ext/ret

and fully stowed switches.

41 Turntable Rotate

Joystick

Value at 5.0 V

Limited Speed and Direction frozen at

zero and neutral, Alarm sounds.

Power up controller with

problem corrected.

Value too high

Value too low

Value at 0 V

Not Calibrated Initiate 1 second beep of Alarm.

Calibrate Joystick.

Just calibrated Initiate 1 second beep of Alarm.

Self-clearing (transient)

42 Turntable Rotate

Directional Valves

Fault

Limited Speed and Direction frozen at

zero and neutral, Alarm sounds.

Power up controller with

problem corrected.

43 Turntable Rotate

Flow Valve

Value too high Limited Speed and Direction frozen at

zero and neutral, Alarm sounds.

Power up controller with

problem corrected.

Value too low

Not Calibrated Normal function except threshold for

one or the other direction is zero.

Display message on LCD.

Calibrate valve threshold.

Just calibrated Initiate 1 second beep of Alarm.

Self-clearing (transient)

44 Drive Enable

Override Switch

Fault

Drive enable override direction is

frozen at neutral.

Power up controller with

problem corrected.

45 Platform Level

Switch

Fault

Platform level frozen at neutral.

Power up controller with

problem corrected.

46 Primary Extend /

Retract Switch

Fault

Platform Extend / Retract frozen at

neutral.

Power up controller with

problem corrected.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Terex Genie Z-40, Service And Repair Manual, Page: 105 / 287

Search results

Summary of Contents for Genie Z-40

Reviews: