Terex Genie Z-40 Service And Repair Manual Download Page 97

Page: 97 / 287

June 2022

Service and Repair Manual

Track Components

Part No. 1268555GT

-62/40

Track C ompone nt s

11-1 Tr ack Asse mbly

11-1

Track Assembly

How to Remove a Track

Assembly

Note: Perform this procedure with the machine on

a firm, level surface with the boom in the stowed

position.
1 Select a track assembly to remove. Loosen

and remove as many sprocket retaining

fasteners as possible from the hub adapter.

2 Drive the machine in either direction just

enough to access the remaining fasteners. Do

not remove the retaining fasteners.

3 Chock the tracks at the opposite end of the

machine to prevent the machine from rolling.

4 Center a lifting jack of ample capacity

(20,000 lbs / 10,000 kg) under the drive

chassis between the tracks.

5 Lift the machine until the tracks are off the

ground and then place jack stands under the

drive chassis for support.

6 Attach a lifting strap from an overhead crane

to the center-point of the track assembly,

above the sprocket.

7 Remove the remaining sprocket retaining

fasteners from the hub adapter.

8 Carefully remove the track assembly from the

drive hub and set aside.

Crushing hazard. The track

assembly could become

unbalanced and fall when

removed from the machine if

not properly supported by the

overhead crane.

How to Replace the Track

Note: Perform this procedure on a firm, level

surface with the machine in the stowed position.
1 Remove the track assembly from the

machine. Refer to Repair Procedure,

How to

Remove a Track Assembly

Note: The sprocket is comprised of two halves.

Before removing the track assembly from the

machine and to ease the removal of the sprocket,

drive the machine until one complete half of the

sprocket is located above the undercarriage of the

track assembly.
2 Loosen the grease plug on the track tension

cylinder to relieve the track tension. Clean up

any grease that has spilled.

3 Remove the 2 sprocket retaining fasteners.

Remove the sprocket half from the track

assembly.

4 Carefully remove the track from the

undercarriage.

5 Use an overhead supporting device to lay the

undercarriage on its side with the drive

sprocket bearing assembly facing upward and

the track tension cylinder towards the ground.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands