Terex Genie Z-40 Service And Repair Manual Download Page 144

Page: 144 / 287

Service and Repair Manual

June 2022

Schematics

130

-62/40

Part No. 1268555GT

Secti on 5

Schematic s

Intro ductio n

Observe and Obey:



Troubleshooting and repair procedures shall

be completed by a person trained and

qualified on the repair of this machine



Immediately tag and remove from service a

damaged or malfunctioning machine.



Repair any machine damage or malfunction

before operating the machine.

Before Troubleshooting:



Read, understand and obey the safety rules

and operating instructions in the appropriate

operator's manual on your machine.



Be sure that all necessary tools and test

equipment are available and ready for use.

About This Section

There are two groups of schematics in this section.

Electrical Schematics

Electrocution/burn hazard.

Contact with electrically charged

circuits could result in death or

serious injury. Remove all rings,

watches and other jewelry.

Hydraulic Schematics

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands