Terex Genie Z-40 Service And Repair Manual Download Page 17

Page: 17 / 287

June 2022

Service and Repair Manual

Specifications

Part No. 1268555GT

-62/40

Do not top off with incompatible

hydraulic fluids. Hydraulic fluids

may be incompatible due to the

differences in base additive

chemistry. When incompatible

fluids are mixed, insoluble

materials may form and deposit

in the hydraulic system,

plugging hydraulic lines, filters,

control valves and may result in

component damage.

Note: Do not operate the machine when the

ambient air temperature is consistently above

120°F / 49°C.

Hydraulic Fluid Temperature

Range

Ambient air temperature

1  Chevron hydraulic oil 5606A
2  Petro-Canada Environ MV 46
3  UCON Hydrolube HP-5046D
4  Chevron Rando HD premium oil MV

Chevron Rando HD Premium Oil

MV Fluid Properties

ISO Grade

Viscosity index

200

Kinematic Viscosity

cSt @ 200°F / 100°C

cSt @ 104°F / 40°C

7.5

33.5

Brookfield Viscosity

cP @ -4°F / -20°C

cP @ -22°F / -30°C

1040

3310

Flash point

375°F / 190°C

Pour point

-58°F / -50°C

Maximum continuous operating

temperature

171°F / 77°C

Note: A hydraulic oil heating system is

recommended when the ambient temperature is

consistently below 0°F / -18°C.
Note: Do not operate the machine when the

ambient temperature is below -20°F / -29°C with

Rando HD Premium MV.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands