Terex Genie Z-40 Service And Repair Manual Download Page 35

Page: 35 / 287

June 2022

Service and Repair Manual

Platform Controls

Part No. 1268555GT

-62/40

Platf orm Controls

Platform Controls

The platform control box contains one printed

circuit board. The ALC-500 circuit board inside the

platform control box controls all proportional

machine functions from the platform. The joystick

controllers at the platform controls utilize Hall

Effect technology and require no adjustment. The

operating parameters of the joysticks are stored in

memory at the ECM circuit board at the platform

controls. If a joystick error occurs or if a joystick is

replaced, it will need to be calibrated before that

particular machine function will operate. Refer to

Repair Procedure,

How to Calibrate a Joystick

Each joystick controller should operate smoothly

and provide proportional speed control over its

entire range of motion.

1 ALC-500 circuit board

2 drive/steer joystick controller
3 secondary boom up/down joystick

controller

4 primary boom up/down and turntable

rotate left/right joystick controller

1-1 ALC -50 0 Circui t Boa rd

1-1

ALC-500 Circuit Board

Electrocution/burn hazard.

Contact with electrically charged

circuits could result in death or

serious injury. Remove all rings,

watches and other jewelry.

Note: When the ALC-500 circuit board is replaced,

the joystick controllers will need to be calibrated.

Refer to Repair Procedure,

How to Calibrate a

Joystick

How to Remove the ALC-500

Circuit Board

1 Push in the red Emergency Stop button to the

off position at both the ground and platform

controls.

2 Remove the platform control box lid retaining

fasteners. Open the control box lid.

3 Locate the ALC-500 circuit board mounted to

the inside of the platform control box.

4 Attach a grounded wrist strap to the ground

screw inside the platform control box.

Component damage hazard.

Electrostatic discharge (ESD)

can damage printed circuit board

components. Maintain firm

contact with a metal part of the

machine that is grounded at all

times when handling printed

circuit boards OR use a

grounded wrist strap.

5 Carefully disconnect the wire connectors from

the circuit board.

6 Remove the ALC-500 circuit board mounting

fasteners.

7 Carefully remove the ALC-500 circuit board

from the platform control box.

Summary of Contents for Genie Z-40
































































































































































































































































































Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands

Terex Genie Z-40, Service And Repair Manual

Search results

Summary of Contents for Genie Z-40

Reviews:

Related manuals for Genie Z-40

Brands by name

Popular brands