manualshive.com logo in svg

Terex Genie Z-40, Service And Repair Manual, Page: 43 / 287

Share
Download
Terex Genie Z-40 Service And Repair Manual Download Page 43

June 2022

 

Service and Repair Manual

 

 

Platform Components

 

 

 

Part No. 1268555GT

 

Z

®

-62/40

 

29 

 

 

 

4  Remove the pivot pin retaining fasteners from 

the jib boom and jib boom leveling arms to the 

platform rotator. Do not remove the pins. 

5  Support the jib boom leveling arms. 

 

Bodily injury hazard. The jib 

boom leveling arms may fall if 

not properly supported. 

6  Use a soft metal drift to drive both pins out, 

then remove the platform rotator from the 

machine. 

Note: When installing the platform rotator 

fasteners, torque the fasteners to specifications. 

 

How to Bleed the Platform 

Rotator 

Note: This procedure will require two people. Do 

not start the engine. Use auxiliary power for this 

procedure. 
1  Move the function enable toggle switch to 

either side and activate the platform rotate 

toggle switch to the right then the left through 

two platform rotation cycles, then hold the 

switch to the right position until the platform is 

fully rotated to the right. 

2  Place a suitable container underneath the 

platform rotator. 

3  Open the top bleed screw on the rotator, but 

do not remove it. 

 

Bodily injury hazard. Spraying 

hydraulic oil can penetrate and 

burn skin. Loosen hydraulic 

connections very slowly to allow 

the oil pressure to dissipate 

gradually. Do not allow oil to 

squirt or spray. 

4  Move the function enable toggle switch to 

either side and hold the platform rotate toggle 

switch to the left position until the platform is 

fully rotated to the left. Continue holding the 

toggle switch until air stops coming out of the 

bleed screw. Close the bleed screw. 

 

Crushing hazard. Keep clear of 

the platform during rotation. 

 

Summary of Contents for Genie Z-40
































































































































































































































































































Reviews:

No comments