Telit Wireless Solutions LE910C series Page 1134 At Commands Reference Manual Download

Page: 1134 / 1904

Page 1134

LE910Cx AT Commands Reference Guide

80502ST10950A Rev. 14

Page 1134 of 1904

2022-03-04

Not Subject to NDA

The default value of parameter <mode> for pin0, pin2 and pin3 is 2
in LE910C1-EU/NF/LA (4G+2G).

For LE910C1-EUX/SAX/SVX and LE910Cx-WWX product:

- Not support CTS/RTS/RXD/TXD/DTR pins

- Not support GPIO Kernel mode

- DTR pin can't be set as GPO when #M2MATP is '1'.

AT#V24CFG?

Read command returns actual mode for all the pins (either output and
input) in the format:

#V24CFG: <pin1>,<mode1>[<CR><LF><CR><LF>
#V24CFG: <pin2>,<mode2>[...]]

AT#V24CFG=?

Test command reports supported range of values for parameters
<pin>,<mode> and <save>.

«
...
1132
1133
1134
1135
1136
...
»

Summary of Contents for LE910C series

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands

Telit Wireless Solutions LE910C series, At Commands Reference Manual

Search results

Summary of Contents for LE910C series

Reviews:

Related manuals for LE910C series

Brands by name

Popular brands